2 measurements taken within a single day, net +12. Dots are measurements; the straight line between them is drawn to join them, not to claim we know the path taken in between — snapshots are recorded only when a count changes, so gaps mean “no change observed”, never “interpolated”. The vertical axis spans 2,087–2,103 and does not start at zero.
Measurement log — every subscribers count we have recorded
Measured (UTC)
Subscribers
Change
10 Aug 2026, 15:01
2,101
+12
9 Aug 2026, 19:46
2,089
first reading
Engagement
18 posts held, back to 29 July 2026 — the reader has not yet reached the start of this channel’s public history, so older posts may sit further back, unread. Read across 1 pageof Telegram’s post history, 20 posts per page.
ERR · 30 days
28.1%
avg views ÷ 2,101 subscribers
Avg views / post
589
18 posts measured
Reaction rate
0.644%
reactions ÷ views · ER floor
Posts in window
18
of 18 held
ERR is average views per post over the last 30 days divided by subscribers, the definition TGStat uses, so this figure is comparable with the one you will see elsewhere. It falls structurally as a channel grows: a high ERR on a small channel and a low one on a large channel describe reach mathematics, not quality. We publish the figure and the sample it came from and pass no verdict on it.
ER is defined industry-wide as (forwards + reactions + comments) ÷ views— note the denominator is views, not subscribers. Telegram’s public web preview carries views and reactions but not forward or comment counts, so the reaction rate above is the reactions term only and is therefore a floor: the true ER for this channel is higher by an amount we have not measured and will not estimate. It is computed over the 17 of 18 measured posts that carry a reaction reading, and over those same posts' views.
What these figures were computed from
Window
Rolling 30 days · latest post in window 8 August 2026
Posts held
18 (29 July 2026 – 8 August 2026)
Views total
10,608
Reactions total
63
Forwards / comments
not exposed by the public surface — not measured, not estimated
Readings taken
9 Aug 2026, 19:46 UTC
Views are a single reading per post, taken at the time above. A post published in the last day or two is still accumulating views, which pulls the 30-day average down slightly. That is a property of the standard definition rather than a fault in it, so we keep the definition rather than “correcting” the number into something nobody can reproduce.
Precision. Telegram publishes view counts on its public widget in short form — 8.12K, 3.7M — so any reading at or above 1,000 reaches us rounded to three significant figures, and only counts below 1,000 are exact. Averages and rates derived from them are shown to the same precision rather than to the unit: a figure like 3,701,250 would assert digits nobody measured.
Reaction counts are published per emoji and rounded the same way, so a total below 1,000 is exact and a larger one is a sum that may carry a rounded component from each emoji above 1,000. Because it is a sum, it does not look rounded — read a large reaction total as three significant figures per contributing emoji rather than as the figure it prints.
What this channel posts
Video runtime
2m 00s
Average length
24s
Measured directly from 5 videos with a duration reading, out of the posts we hold for this channel — not this channel’s whole posting history, only the sample this register has actually read. An exact reading to the second, taken from the post itself rather than from Telegram’s own rounded chrome, so it carries no ≈ mark.
Reaction mix
63 reactions across 16 posts, in 3 distinct kinds. The most used accounts for 69.8% of them.
Every reaction kind recorded on the sample, most used first
Reaction
Count
Share
Share, drawn
❤
44
69.8%
🔥
14
22.2%
👍
5
7.94%
No sentiment is inferred, and none should be read in. This table is ordered by count and by nothing else. Emoji do not carry stable meaning across languages or communities — 🙏 is thanks in one channel and mourning in another — so we publish which ones were pressed and how often, and pass no judgement on what an audience meant by them.
Precision. Telegram publishes reaction counts per emoji and short-forms each one — 4.34K, 1.2M — so any single kind at or above 1,000 reaches us at three significant figures, and only counts below 1,000 are exact. The shares above are ratios of those figures and carry the same error. This is also why the total here can differ slightly from a reaction total printed elsewhere on the page: both are sums of the same rounded parts, taken over samples with different edges.
Coverage. Reactions were read on 17 of the 18 sampled posts in this sample. Summed by Telegram’s own count on each post — not by adding up the per-emoji breakdown above — those same posts carry 63reactions in total: the kind of figure the paragraph above means by “a reaction total printed elsewhere on the page”.
Measured over the 18 most recent posts we hold, published 29 July 2026 to 8 August 2026, using the newest reading held for each. Telegram Stars are excluded: they are a payment, not a reaction, and they have their own section.
نتیجهگیری استراتژیک برای شروع کسبوکار: همانطور که دیدید، انتخاب فیلامنت تنها نیمی از مسیر است؛ نیمه مهمتر، «انتخاب ابزار تولید» است. شما نمیتوانید سفارش یک قطعه صنعتی ABS بگیرید در حالی که پرینتر شما محفظه بسته ندارد. نمیتوانید با یک دستگاه اقتصادی ساده، وارد بازار پرسود واشرهای لاستیکی TPU شوید.
دستگاه پرینتر سهبعدی شما یک اسباببازی نیست، بلکه دستگاه چاپ پولِ کسبوکار شماست. انتخاب پرینتر باید دقیقاً بر اساس…
متریال Nylon / نایلون (لیگ برترِ مقاومت سایشی) فوقالعاده مستحکم و مقاوم در برابر سایش. پادشاه قطعات مهندسی.
💰 بازار هدف: چرخدندههای صنعتی، بوشها و قطعات تحت اصطکاک مداوم.
🖨 دستگاه مورد نیاز: پرینتر حرفهای با هاتاند تمامفلزی (توانایی چاپ در دمای بالای ۲۵۰ درجه) و محفظه بسته.
🛠 نکته پسپردازش: نایلون به شدت جاذب رطوبت است. برای چاپ بدون نقص، حتماً باید یک دستگاه «خشککن فیلامنت» داشته باشید. نکته جالب اینکه قطعا…
متریال ABS (استانداردِ سختِ صنعتی) فیلامنتی با مقاومت حرارتی عالی. قطعات چاپ شده با ABS در داشبورد ماشین در اوج تابستان هم تغییر شکل نمیدهند.
💰 بازار هدف: قطعات پلاستیکی داخل موتور خودرو، کیسهای الکترونیکی و قطعات تحت فشار.
🖨 دستگاه مورد نیاز: حتماً به پرینتری با محفظه بسته (Enclosure) و هیتبد قوی (دمای بالای ۱۰۰ درجه) نیاز دارید. چاپ ABS در پرینترهای فضای باز باعث ترکخوردگی قطعه میشود.
🛠 نکته پسپردازش (فوقالع…
متریال TPU (ورود به بازار پرسود قطعات انعطافپذیر) فیلامنتی لاستیکی و منعطف که حاشیه سود بسیار بالایی دارد، چون هر کسی توانایی چاپ تمیزِ آن را ندارد.
💰 بازار هدف: واشرهای صنعتی نایاب، ضربهگیرهای سفارشی، کفی کفش طبی و قابهای منعطف.
🖨 دستگاه مورد نیاز: بسیار مهم! برای چاپ راحت TPU، پرینتر شما ترجیحاً باید مجهز به اکسترودر «دایرکت درایو» (Direct Drive) باشد. پرینترهای «باودن» (Bowden) در چاپ این متریال نرم، شما را به …
۲. متریال PETG (دوام صنعتی با کاربری آسان) وقتی مشتری قطعهای میخواهد که در برابر ضربه، رطوبت و مواد شیمیایی مقاومت کند، PETG برگ برنده شماست.
💰 بازار هدف: قطعات محیطهای باز (Outdoor)، تجهیزات گلخانهای، قابهای محافظ و استندهای فروشگاهی.
🖨 دستگاه مورد نیاز: پرینترهای استاندارد با صفحه گرم (حدود ۷۰-۸۰ درجه). نیازی به محفظه بسته ندارد اما بهتر است دستگاه شما هاتاند (Hotend) تمامفلزی داشته باشد.
🛠 نکته پسپردازش: ا…
۱. متریال PLA (ماشینِ پولسازی سریع و بیدردسر) پرکاربردترین فیلامنت جهان. در دمای پایین (۱۹۰-۲۲۰ درجه) چاپ میشود و کمترین میزان تاببرداشتن (Warping) را دارد.
💰 بازار هدف: تولید نمونههای اولیه (پروتوتایپ)، قالبسازی سریع، ماکتهای معماری و محصولات دکوری.
🖨 دستگاه مورد نیاز: به پرینتر پیچیدهای نیاز ندارد. با اقتصادیترین پرینترهای با ساختار باز (Open-Frame) و حتی بدون هیتبد (صفحه گرم) هم به راحتی چاپ میشود.
🛠 نک…
انتخاب متریال اشتباه = دور ریختن سود پروژه! (راهنمای تجاری ۵ فیلامنت اصلی)
در کسبوکار پرینت سهبعدی، «بهترین فیلامنت» وجود ندارد؛ بلکه «فیلامنتِ سودآور» برای هر پروژه متفاوت است. اگر کاربرد قطعه را ندانید، حتی با گرانترین متریالها هم مشتری را از دست میدهید.
در ادامه به عنوان مشاورین ورود به صنعت پرینت سهبعدی، ۵ متریال اصلی بازار کار را با تجهیزات مورد نیازشان تحلیل کردهایم:
🔹 ابزار Tripo (بهترین محیط ویرایش):
این ابزار یکی از بهترین هوش های مصنوعی برای تبدیل عکس به فایل سه بعدی یا ایجاد فایل با اسکچ(توضیحات) است.
مزیت این ابزار در ویرایش طرح سه بعدی خروجی AI است که میتواند طرح را به قسمت های مجزا تبدیل کند و تنطیماتی را به هدف شخصی سازی برای هر قطعه انجام دهد.
این ابزار برای طراحان کانسپت و مدلهای رومیزی ایدهآل است اما در حالت رایگان محدودیت تولید فایل دارد.
🔹 ابزار Meshy (متخصص جزئیات و فیگور):
یکی از بهترین ابزارها برای کسانی که میخوان فیگور و مدلهای تزئینی رو چاپ کنن و بفروشن.
این ابزار علاوه بر تولید مش روی بافت دهی و جزییات هم تمرکز بالایی دارد. قابلیت محبوب این نرم افزار اصلاح خودکار شکل ها و نقوش هندسی هست و همچنین قابلیت اتصال مستقیم به بیشتر اسلایسر ها را هم دارد.
اگر کار شما طراحی فیگور است و ظاهر نهایی و رنگ محصولات براتون خیلی مهمه این ابزار بهترین انتخاب …
🔹 ابزار Hitem3D (Hi3D) (تمرکز بر قابلیت چاپ):
این مدل بر خلاف رقبا تمرکز کمتری روی ویژگی هی بصری دارد و هدف آن تولید مدلی است که مستقیما برای چاپ آماده باشد. همچنین این ابزار قابلیت اتصال مستقیم به فضای bambulab متصل می شود و طراحی کاربری و کار با آن بسیار بهینه و راحت است.
اگر شما صرفا به دنبال طراحی یک فایل با جزییات کمتر هستید که میخواهید خیلی سریع برای چاپ آماده وبهینه باشد بهتر است از این ابزار استفاده کنید.
اجازه بدید شفاف باشم؛ هیچکدوم از این ابزارها هنوز به طور صددرصد جایگزین یک طراح حرفهای نشدن. مدلهای خروجی معمولاً برای یک چاپ بینقص نیاز به کمی اصلاح و رفع ارور دارند.
اما ارزش بیزینسی و واقعی این ابزارها کجاست؟
اینکه فاصله شما رو از "یک ایده خام" تا "رسیدن به یک فایل قابل پرینت" از چند روز، به چند دقیقه کاهش میدن.
در دنیای تولید، زمان یعنی پول. این ابزارها با کاهش شدید هزینههای اولیه، حاشیه سود شما رو در فروش …
تبدیل عکس به محصول پولساز! چطور با هوش مصنوعی هزینههای طراحی رو دور بزنیم؟ 💸
پایان یک مانع بزرگ!
تا حالا شده تو اینستاگرام یا پینترست یه دکوری خاص، یه فیگور جذاب یا حتی یه قطعه کاربردی ببینید و با خودتون بگید:
«اگر میتونستم اینو بسازم و بفروشم چقدر عالی میشد...»؟
خیلی از افرادی که به فکر راهاندازی کسبوکار و درآمدزایی با پرینتر سهبعدی هستند، دقیقاً همینجا متوقف میشن! چرا؟ چون فکر میکنن برای شروع حتماً باید ی…
❤5🔥1
Showing the 12 most recent of 18 posts we hold for @printerland3dfiles. View and reaction counts are the latest single reading for each post, not a live figure, and a recent post is still accumulating both. A view count marked ≈ was rounded by Telegram before we ever saw it — t.me prints views in full below 1,000 and to three significant figures above, so ≈1,200,000 means somewhere between 1,150,000 and 1,249,999. Unmarked counts are exact. Text is reproduced from the public post preview and truncated for length.
Citation-graph rank
Citation-graph rank — 897,349 of 1,160,990entries in the measured graph. A weighted position computed from the forward and mention edges below — republished posts weigh more than named mentions — and recomputed periodically, over the whole graph. Published only as this ordinal position, never as a score: a position is a fact, and a score printed beside one channel’s name would read as a verdict this register does not make. The two counts beneath stay separate for the same reason mentions are never summed with forwards anywhere else on this page — a named-by count costs nothing to manufacture. The top 100 by this measure, or how it is computed.
Forward network
Republished by
Channels on the register that have forwarded this channel's posts into their own feed.
Built only from forwarded posts we have actually read, on both sides. Coverage is early and deliberately incomplete: a missing link means we have not read the post that would prove it, never that the relationship does not exist. Counts are distinct forwarded posts observed, so they only ever go up as we read more.
Cite this entry
A live page changes as we take new readings, so a citation should name the measurement it is based on, not just the URL. The line below cites the subscriber count as measured 10 August 2026 — this
entry's latest reading, not the date you are reading this.
“پرینترلند | کسب درآمد با پرینتر سه بعدی” (@printerland3dfiles), 2,101 subscribers as measured 10 August 2026. Telegram Register, tgregister.com/channel/printerland3dfiles.
Full measurement history, CC BY 4.0. Every reading this register holds for this entry, not just the latest one, as a dated, downloadable record: CSV · JSON. Free to use with attribution to tgregister.com. Each file carries its own generation timestamp, which is the figure to cite for exactly when the data was retrieved.